长沙凯运印刷器材有限公司 | |
联系人: | 赵庆国 经理 |
手机: | 18975163775 |
电话: | 0731-89713375 |
传真: | 0731-84158275 |
Q Q : | |
Email: | 1256508549@qq.com |
地址: | 长沙市雨花区中意一路红星农民新村80栋 |
商铺: | http://mf6666.ccedwy.com/ |
长沙供应电镀环保油墨,电镀陶瓷环保油墨,电镀环保油墨
产品数量:不限
有效期至:180天
更新时间:2012-12-28 09:55:33
1、 可直接丝印或移印在喷过PU光油的塑胶材料上,无需加固化剂,有良好的附着力,耐酒精、耐摩擦。
2、 加入8%-10%的DS-10\70固化剂,无需烘烤,可附着在塑胶电镀面、五金、五金电镀面、玻璃、强化板材、喷UV面、赛钢等特殊材料上,有良好的附着力,耐酒精、耐摩擦。(注:加入固化剂的测试时间为24小时以后)。
印刷:
选用网目为250-400目,丝印移印均可。
表干及实干时间:
表干时间自然挥发5-10分钟,实干时间在24小时以内。如需快速干燥请烘烤75度30分钟。
稀释及清洗:
1、 用783慢干开油水开油。
2、 用718洗网水洗网。
测试方法(完全干燥后)
1、3M胶纸粘在画有百格的油墨表面45度角迅速拉起不脱油,
2、纯度99%的酒精500G力在油墨表面来回擦拭500次无脱色。
使用方法:
1、 使用前应充分搅拌,用后随时密封。
2、 搅拌时加开油水10-15%,稀释到印刷粘度;
3、 网版塞网时间可用洗网水清洗:
4、 不得与其它类型油墨混合使用:
注意事项:
1、 塑料、五金及电镀材料的外观相似,但可能会是不同的材料,客户需试印确其符合要求后,再批量印刷;
2、 加过固化剂的油墨要在4小时内用完。
3、 环境温度过高,将会影响油墨原有质量;
4、 请远离火源,阴暗环境下存放
Special features:
1, can be directly screen printing or pad printing in the gush after PU light oil of plastic material, without curing agent, has the good adhesion, resistance to alcohol, rubbing.
2, add 8% - 10% of the DS - 10\70 curing agent, without baking, can adhere to the plastic plating surface, metal, metal plating surface, glass, strengthen the plank, spray UV surface, the steel and other special material, has the good adhesion, resistance to alcohol, rubbing. (note: add hardener test time for 24 hours later).
Printing:
Choose screen for 250-400 mesh, silk screen pad printing all can.
Table dry and work time:
Dry time table natural volatile 5-10 minutes, action time in within 24 hours. If you need rapid drying please baking 75 degrees 30 minutes.
Dilution and cleaning:
1,